大家好我是天成照明LED燈珠廠家小編燈漂亮今天我們來介紹LED燈珠BIN電阻 led燈珠阻值大概多少的問題，以下就是燈漂亮對此問題和相關問題的歸納整理,一起來看看吧。

文章目錄導航:

• 1、LED燈珠阻值
• 2、led燈珠電阻多少
• 3、燈珠加電阻怎么調節
• 4、led燈珠壞了用多大的電阻代替
• 5、led燈珠壞了用多大電阻代替

LED燈珠阻值

一、2V左右點亮的LED燈(如紅、黃、橙等)：12V：470歐車上12V：680歐

二：3V左右點亮的LED燈(如藍、綠、白等)：12V：390歐車上12V：470歐電阻的參數一般有兩個，阻值R和功率P。R=（U-Uled）/Iled，USB的標準電壓是DC5V的，所以R=（5-Uled）/IledUled，燈珠的正向導通電壓。Iled，燈珠的正向導通電流。

現在LED有很多種類，顏色不同，一般電流也不同。電阻大小影響電流大小，進而影響燈珠的亮度，但只要不超過正向最大電流，都可以使用，只是亮度或有不同，所以選擇范圍比較大。

led燈珠電阻多少

小功率紅黃的,它的電阻=電壓/電流=1.8/0.02=90Ω

小功率藍綠的,它的電阻=電壓/電流=3.2/0.02=160Ω

大功率紅黃的,它的電阻=電壓/電流=2.2/0.35=6Ω

大功率藍綠的,它的電阻=電壓/電流=3.4/0.35=10Ω

電阻是一個物理量，在物理學中表示導體對電流阻礙作用的大小，它的英文名稱為resistance，通常縮寫為R。

它是導體的一種基本性質，與導體的尺寸、材料、溫度有關。導體的電阻越大，表示導體對電流的阻礙作用越大。不同的導體，電阻一般不同。

燈珠加電阻怎么調節

Led燈珠線路上串加電阻，一般是為了限流，在預設的工作電流值出發去按供電電壓去算出需要加的電阻值，同時加裝的電阻上也有相應壓降。比如燈珠工作電流設置為10mA，所需電壓為3V，現有電壓為5Ⅴ，顯然電壓高出2V，用2V÷10mA=2÷0.01=200歐姆，電阻上壓降為2V，燈珠上為3V，電流為10mA。如果不清楚燈珠具體參數，也可先串一個電位器(可變電阻)，從大阻值向下調節，直到燈珠點亮和亮度適中時，測一下電位器實用的電阻值換上固定電阻即可。

led燈珠壞了用多大的電阻代替

180歐姆。

這種燈珠壞了，如果你手頭沒有LED燈珠，可以用150-180Ω左右的電阻代替，若是恒流源驅動可以直接短接原燈珠線路兩端即可。

當然，如果拆開里面沒有燒壞的痕跡，則找同類的電源先更換試試。不同的現象，不同的處理方法。要首先知道，是電源驅動電路的問題，還是燈珠本身的問題。

led燈珠壞了用多大電阻代替

LED燈珠壞了可以用電阻代替。電阻值R=U/I。式中，U為燈珠的正常工作電壓，I為燈珠正常發光時的電流。

以上就是天成小編對于LED燈珠BIN電阻 led燈珠阻值大概多少問題和相關問題的解答了，希望對你有用 【責任編輯：燈漂亮】