大家好今天來介紹led燈珠充電電路(充電led手電筒如何維修)的問題，以下是小編對此問題的歸納整理，來看看吧。

文章目錄列表:

• 1、LED手電筒充電時候燒了怎么維修
• 2、12個led燈珠手電的充電電路能給18650電池充電嗎
• 3、led燈珠怎么用電池供電
• 4、用5v600mA的手機充電器接兩個串聯LED貼片燈珠需要串一個多大的限流電阻
• 5、5v充電器接3vled燈珠方法

LED手電筒充電時候燒了怎么維修

LED充電式手電筒一般內置4V蓄電池，并采用簡單的阻容降壓電路來給蓄電池充電，使用時故障率較高。下面我們結合這種手電筒的電路原理圖來介紹一下如何修理這種手電筒。▲ 充電式LED手電筒電路原理圖。

上圖為普通的充電式LED手電筒的電路原理圖。手電筒充電時，AC220V經電容C降壓限流及整流橋整流后，給內置的4V蓄電池充電。LED1為充電指示燈，與之串聯的300Ω電阻為限流電阻。K為手電筒的電源開關。由于提問者未說充電時手電筒哪里燒壞了，下面我們來分析一下這種手電筒充電時可能燒壞的元件。

上圖中的LED2為照明用的白光LED燈珠，由于這種手電筒的充電電路較簡單，在充電時蓄電池兩端的電壓較高，此時不能閉合開關K使燈珠LED2點亮，否則很容易燒壞燈珠。若是充電時LED燈珠燒壞，在確認無其他故障時，只要拆掉壞的燈珠，換上同規格的新燈珠即可。▲ 充電式LED手電筒的電路板。▲ 充電式LED手電筒。

充電式LED手電筒內部的降壓電容C一般要求耐壓值≥400V，若該電容的耐壓值選的較低或AC220V電源電壓偏高，便可能會將這個電容擊穿，這樣便會導致電路中出現較大的電流。為了避免大電流下損壞更多的元器件，有的手電筒電路板上會在AC220V輸入端串入一個幾歐的小電阻或者將輸入端PCB板的一小段銅箔制作的很細，這樣因故障而出現大電流時，這個小電阻或較細的PCB板銅箔便會燒壞。若是這種情況，首先更換一個耐壓值符合要求的同容量電容，然后再將燒壞的PCB板銅箔或小電阻連接即可。

若想了解更多的電子電路及元器件知識，請關注我，謝謝。

12個led燈珠手電的充電電路能給18650電池充電嗎

想改裝普通LED手電筒的電池為鋰電池是吧

可以啊(a)不過需要另外添加一個充電控制電路。原手電筒的充電電路不能直接用于鋰電池。X寶上就有鋰電池充電模塊賣，幾塊錢一個。

我手頭就有一個普通的LED燈，自己改裝了鋰電池。

原手電筒是鉛酸電池的，重量大容量還小。鋰電池輕，容量還大。

led燈珠怎么用電池供電

led燈珠怎么用充電器的電壓一般是4.7-5.6V，LED燈珠額定電壓一般3-3.6V，科瑞的電壓偏低，一般在3.1V左右，如果不加限流，直接接到5V上去，電流會很大，燈珠用不了多久就會燒壞。剛接上可以點亮，而且很亮，但點的時間長了，燈珠很快就會被燒壞。

不可以。照明用高亮度LED的工作電壓大約是3.2V左右，工作電流在100mA左右，如果你直接使用充電器連接的話，將會很快燒毀LED。二、不可以。原因同上三、不一定。如果是使用變壓器進行充電或者是開關電源電路進行充電，那么基本上可以在充電的同時使用LED，但是對于使用電容器限流的簡易恒流式充電電路（就是常見的廉價的那種充電式手電筒內部的充電電路），就絕對不可以在開燈的情況下充電。

贊一下

用5v600mA的手機充電器接兩個串聯LED貼片燈珠需要串一個多大的限流電阻

根據提問者的意思，想使用5V/600mA的手機充電器點亮兩個LED貼片燈珠，由于沒有給出LED燈珠的具體型號，為止LED燈珠的工作電壓及功率等，下面做分類分析。

先說一下限流電阻的計算方法：

首先要知道LED燈珠的正向壓降V和工作電流I，明確LED燈珠的型號會有相應的工作電壓及工作電流等參數。

那么限流電阻R的計算方法為：R=(VIN-V)/I。

若為n個LED燈珠串聯，則限流電阻R=(VIN-n×V)/I。

LED燈珠其實就是一個二極管，需要正向的導通電壓就能工作，一般2~3.6V，通過電流大小控制LED燈珠的亮度，LED燈珠實際是將電能轉換為光能。

黃光和紅光LED的工作電壓一般為1.8~2.4V，而藍光、白光、綠光LED燈珠的工作電壓一般為3~3.6V。

小功率的LED燈珠工作電流一般為10~20mA,大功率LED燈珠工作電流可達100mA/350mA甚至更高。

提問者使用5V的手機充電器點亮兩個LED燈珠，由于燈珠具體型號未知：

（1）若為黃光和紅光LED，工作電壓1.8~2.4V左右，可以兩個LED燈珠串聯，串聯后限流電阻的計算：若按工作電流10mA計算，壓降按2V計算，則限流電阻R=(5V-2V×2)/10mA=100Ω。

若只串一個LED，則限流電阻R=R=(5V-2V)/10mA=300Ω。

（2）若為藍光、白光、綠光LED燈珠，其工作電壓為3~3.6V左右，這時兩個LED燈珠串聯使用5V的充電器是無法點亮的，只能采用并聯的方式。

限流電阻計算：若工作電流依然為10mA,工作電壓按3.3V計算，則限流電阻R=(5V-3.3V)/10mA=170Ω。

限流電阻的目的是限制LED的工作電流，LED的工作電流與限流電阻成反比例關系，限流電阻越大工作電流越小，LED燈珠的亮度越暗；反之，限流電阻越小工作電流越大，LED燈珠的亮度越亮。但是電流的選取必須在LED燈珠的最大正常工作電流以內。

以上是本人觀點，想了解更多知識請關注我，謝謝

5v充電器接3vled燈珠方法

首先看led的工作電流是多少，然后串聯一個合適的電阻,接到充電器上就可以了。

以上就是小編對于led燈珠充電電路(充電led手電筒如何維修)問題和相關問題的解答了，希望對你有用