萬用表檢測led燈珠漏電 如何用萬用表測led燈是否損壞 |
| 發布時間:2022-09-21 12:34:42 |
大家好我是小編一夢今天我們來介紹萬用表檢測led燈珠漏電 如何用萬用表測led燈是否損壞的問題，以下就是一夢對此問題和相關問題的歸納整理,一起來看看吧。 文章目錄導航: 燈已裝好怎么用萬能表查漏電 1、用萬用表測量漏電電壓。把萬用表轉換開關放在交流電壓測量檔上，一般為250V檔位，然后把黑表筆插入所測設備附近的土壤里，紅表筆接在設備的金屬外殼上。這時看萬用表上指示數，如果表針不動，可依次改放低檔，直到指示出具體的數據即為該設備的漏電電壓。如果表筆在最低檔時仍無指示，即表示該設備不存在漏電現象。 2、用驗電筆檢查是否漏電。檢查者手握驗電筆直接與用電設備的金屬外殼相接，當驗電筆中的氖管發亮時，即說明該設備有漏電現象，且漏電電壓較高。當氖管不亮時，則可能是漏電電壓低氖管亮不起來，也可能就沒有漏電電壓。
怎么用萬用表測LED燈箱是否漏電 嚴格的說LED測試漏電流是要用專業的光電測試儀的,如果沒有專業設備可以用萬用表來粗測下,用指針萬用表(47型)電阻*10K檔黑筆接LED正極,紅筆接LED負極,這時的電阻很的小,并且同時LED會點亮,這就說明LED是完好的,要測漏電流需要把表筆對調一下,也就是測LED的反向電阻,這時需要把萬用表切換到歐姆*10K擋,測出的電阻應該是無窮大或者指針只是輕微擺動,如果電阻很小就說明LED漏電或是漏電流過大,阻值越小說明漏電流越大,漏電流很大的LED則是不合格產品,如果指針擺到頭說明這只LED報廢了. 萬用表檢測led燈漏電 嚴格的說LED測試漏電流是要用專業的光電測試儀的,如果沒有專業設備可以用萬用表來粗測下,用指針萬用表(47型)電阻*10K檔黑筆接LED正極,紅筆接LED負極,這時的電阻很的小,并且同時LED會點亮,這就說明LED是完好的, 要測漏電流需要把表筆對調一下,也就是測LED的反向電阻,這時需要把萬用表切換到歐姆*10K擋,測出的電阻應該是無窮大或者指針只是輕微擺動,如果電阻很小就說明LED漏電或是漏電流過大,阻值越小說明漏電流越大,漏電流很大的LED則是不合格產品,如果指針擺到頭說明這只LED報廢了. 萬能表怎么查燈線路漏電 用萬用表電阻最高擋測火線和零線對地阻值，阻值小于一兆歐就是漏電了。 筒燈漏電怎么檢查 LED筒燈測試漏電流是要用專業的光電測試儀的,如果沒有專業設備可以用萬用表來粗測下。 用指針萬用表(47型)電阻*10K檔黑筆接LED正極,紅筆接LED筒燈負極,這時的電阻很的小,并且同時LED筒燈會點亮,這就說明LED是完好的,要測漏電流需要把表筆對調一下,也就是測LED的反向電阻,這時需要把萬用表切換到歐姆*10K擋,測出的電阻應該是無窮大或者指針只是輕微擺動,如果電阻很小就說明LED漏電或是漏電流過大,阻值越小說明漏電流越大,漏電流很大的LED則是不合格產品,如果指針擺到頭說明這只LED報廢了. 以上就是天成小編對于萬用表檢測led燈珠漏電 如何用萬用表測led燈是否損壞問題和相關問題的解答了，希望對你有用 【責任編輯：一夢】 |
