led燈燒燈珠維修 led燈閃一下就不亮了故障解決方法 |
| 發布時間:2022-09-23 12:30:13 |
大家好我是小編榮姐今天我們來介紹led燈燒燈珠維修 led燈閃一下就不亮了故障解決方法的問題，以下就是榮姐對此問題和相關問題的歸納整理,一起來看看吧。 文章目錄導航: 條形led燈壞了怎么維修 1、LED燈珠損壞。這是很常見的故障，一般LED燈珠燒壞時，表面上會有黑點，仔細觀察能夠區分出來，對于這種故障維修，需要配備一把烙鐵，將燒壞的燈珠拆下來更換即可，若沒有LED燈珠怎么辦可使用150Ω左右的電阻代替，若是恒流源驅動可以直接短接。 2、濾波電容失效。簡易的LED燈一般將交流電經過容阻降壓后直接整流，然后通過電容濾波給LED燈珠供電。若該濾波電容失效會導致電壓不穩，直流電壓偏低，從而使LED燈變暗。用萬用表的電容檔測量該濾波電容的容量，若誤差較大，誤差大于30%左右說明該電容已變質，找一個耐壓值以及容量都大于等于該電容參數的電容換上即可。 3、容阻降壓模塊損壞，容阻降壓模塊由一個電容電容和電阻并聯組成，可用萬用表測量其電容、電阻是否損壞，若損壞，找個參數相當的電容、電阻換上即可。
LED燈一閃就不亮了這該怎么維修 LED燈由恒流驅動電路和燈珠兩部分組成，這種燈常見的故障就是燈珠損壞和電源濾波電容損壞（恒流驅動電路中的恒流IC很少損壞），若提問者懂電子技術，可以自己動手修理。 一、LED燈珠損壞 LED燈泡一般密封較嚴，燈珠在密閉空間里長時間工作，若燈珠的工作電流較大，并且散熱不好，燈珠容易因過熱而損壞。有些燈珠處于臨界損壞狀態，接通電源瞬間可能因電流的沖擊，閃一下就壞了，由于LED燈珠一般為多個燈珠串聯，這樣損壞一個，就會導致整串燈珠不亮。 一般燒壞的LED燈珠上面有黑點（見上圖），若手里有相同規格的燈珠，可以將壞的燈珠拆下，換個新的即可。若沒有燈珠，亦可以選用一個十幾Ω以下的小電阻焊接在原來燈珠的位置。 二、恒流驅動電路的故障 現在的LED燈泡一般都采用專用的恒流IC構成恒流驅動電路。這類恒流驅動電路中的恒流IC、電感線圈及整流管一般很少損壞，容易損壞的元件就是那個高壓濾波電容。這類電容皆為電解電容，有些燈泡濾波電容的耐壓值選的較低，若交流220V電壓偏高，可能會導致該電容擊穿損壞，這樣恒流驅動電路無法正常工作，燈也就不會點亮了。遇到電源濾波電容損壞，可以選用相同容量，耐壓值不低于原電容的電解電容代換。 若想了解更多的電子電路及元器件知識， 客廳的LED燈珠經常被燒壞該怎么修理電路需串聯一個多大的電阻 客廳里的LED燈的燈珠經常被燒壞，出現這種情況一般是LED燈珠的驅動電流偏大，再加上燈珠可能散熱不好，這樣便會導致燈珠燒壞。 簡單的阻容降壓恒流驅動電路。 現在的LED燈質量好的其恒流驅動器一般都采用專用的恒流驅動IC設計，驅動電流比較穩定，一般不容易損壞，而一些廉價的LED燈有不少都是采用上圖所示的簡單的阻容降壓恒流驅動電路。這種驅動電路的驅動電流不太穩定，其大小與電容C1的容量、市電電壓的高低有關。若遇到市電電壓偏高，或C1取值偏大，這樣便會導致流過燈珠的電流變大，而LED燈珠在燈罩內，若燈珠的散熱不好，工作時間一長便可能會被燒壞。 簡單的LED恒流驅動電路板。 出現這種情況，我們可以用萬用表測量一下市電電壓是否偏高，降壓電容的容量與燈珠的工作電流是否匹配。若所在地區的市電電壓經常偏高，可以將電容C1的容量適當減小一些。為了防止開燈瞬間浪涌電流損壞燈珠，亦可以適當增大電容C2的容量。另外，若C1找不到合適容量的電容，亦可以在C2兩端并聯一個阻值及功率合適的電阻（具體阻值視實際情況而定），這樣可以對流入LED燈珠的電流進行分流，從而減小燈珠的工作電流，降低其發熱量。 若想了解更多的電子電路及元器件知識， led燈珠擊穿了怎么修好 把燈珠去掉后，在用電烙鐵把它串聯上就行了。LED燈珠分為貼片型和插腳型，新型吸頂燈或LED燈泡，使用的都是貼片型。如果是單個燈，比如電器指示燈，使用的都是插腳型。 插腳型燈珠先用電烙鐵將老舊燈珠加熱取下，再將新的燈珠插上，用錫條焊接。 貼片型燈珠安裝時使用熱風機，如果沒有的話，就用電烙鐵或吹風機最熱檔，對老舊燈珠背面加熱，取下后放上新的燈珠，等待冷卻即可。無論是哪種燈珠，在安裝時一定要注意，燈珠需要區分正負極，無論是插腳型還是貼片型，帶有小孔的一端是負極。 led燈珠壞了怎么修理 用萬用表100歐或10歐檔，電筆頭測量每個LED電珠(注意正負極，反接不亮)，好的燈珠會亮，壞的不亮或很暗。如果串聯電珠，將這顆壞電珠短接焊接即OK。 以上就是天成小編對于led燈燒燈珠維修 led燈閃一下就不亮了故障解決方法問題和相關問題的解答了，希望對你有用 【責任編輯：榮姐】 |
