led燈珠超電流 |
| 發布時間:2022-09-30 16:11:57 |
大家好我是小編燈漂亮今天我們來介紹led燈珠超電流 led燈珠會不會燒壞的問題，以下就是燈漂亮對此問題和相關問題的歸納整理,一起來看看吧。 文章目錄導航:
使用白光led燈珠為什么不能超電壓或超電流 不論是移動電源（標稱5V）還是鋰電池（標稱3.7V），都可以作為led電源。由于電源電壓小于led燈珠工作電壓的2倍，要想led燈珠正常發光，只能并聯使用。直接接電源，存在超壓導致的超流，加速光衰甚至燒毀（一會不久就出現一兩個LED在不斷的閃爍，LED摸上去挺熱的---就是例證。閃爍表明已經損壞）。要讓led工作在正常電壓下（相當于間接維持合適工作電流），必須把電源比led多出的電壓加以分壓，最簡單的就是根據物理學原理，串聯電阻分壓的方法。理論計算方法如下每個支路的電阻阻值（Ω）＝（電源輸出電壓－3V）÷0.02電阻功率（W）＞（電源輸出電壓－3V）×0.02。如果是n個led并聯后共用1個電阻的阻值（Ω）＝（電源輸出電壓－3V）÷n×0.02。電阻功率（W）＞（電源輸出電壓－3V）×n×0.02。注：led是非線性元件，燈珠的內阻不是一個定值，不同工作電流下呈現不同的相當于阻值，實踐中無需計算。
led燈珠電流過大會燒壞嗎 當然了，led燈珠也是有額定電流的當電流過大也會燒壞的。不過相對來說電壓過大對燈珠的影響更大一些，led燈珠就是發光二極管它跟其它的二極管特性上也是差不多的，如果仔細看看其伏安特性曲線就知道了，當在某個點上當電壓略有增加其電流就會產生巨大的增量。 led燈珠電流過大解決辦法 1、LED驅動電源開機瞬間電流過大，這時電器的必然特性，瞬間的電流或電壓都是輸出的1.41倍，不過呢，對電器本身沒有任何危害，屬于正常現象。 2、電源開機瞬間都含有這種峰值電壓的沖擊，整流電路內都專門設計這種限制峰值電壓的保護措施。 LED電流增大超出20MA或者說到30MA50MA對LED燈帶有那些后果 對大功率的LED無所謂，但對草帽、5mm之類的小LED燈珠就要命了，通常這些小的LED額(e)定電流也就20ma，一辦讓其工作在15--18ma，到30MA-50MA，那只能是提早光衰哦，很快玩完的 電流過高對LED燈珠有什么影響 趙盛文的提問，我來回答，那您這驅動電源空載太過高了的話是有影響的，首先您要知道LED燈珠一共需要多大電壓，若,比這電壓高出太多，那燈的壽命會有損壞的，按理說空載電壓應該比帶載高一點，但不能特高請您仔細的查一查好嗎(ma) 以上就是天成小編對于led燈珠超電流 led燈珠會不會燒壞問題和相關問題的解答了，希望對你有用 【責任編輯：燈漂亮】 |
