大家好我是天成照明LED燈珠廠家小編燈漂亮今天我們來介紹led燈珠為什么加電阻 led燈珠如何配限流電阻的問題，以下就是燈漂亮對此問題和相關問題的歸納整理,一起來看看吧。

文章目錄導航:

• 1、led燈珠為什么加電阻
• 2、燈珠加電阻怎么調節
• 3、led燈珠配電阻方法
• 4、Led燈閃怎么加電阻
• 5、led燈珠每隔多少個安一個電阻

led燈珠為什么加電阻

1、led燈加電阻為了降電流。

2、LED燈不是一定要加電阻,如果電源是恒流的,可以不用電阻的。因為LED非線性元件,對電壓很敏(min)感,無法以電壓方式控制,主要是以電流的方式控制LED燈亮度,加電阻只是限流而已,其實加電阻會影響LED燈效率,小功率的LED燈可以忽略電阻上的損耗,而大功率的LED燈是直接用恒流電源供電。

燈珠加電阻怎么調節

Led燈珠線路上串加電阻，一般是為了限流，在預設的工作電流值出發去按供電電壓去算出需要加的電阻值，同時加裝的電阻上也有相應壓降。比如燈珠工作電流設置為10mA，所需電壓為3V，現有電壓為5Ⅴ，顯然電壓高出2V，用2V÷10mA=2÷0.01=200歐姆，電阻上壓降為2V，燈珠上為3V，電流為10mA。如果不清楚燈珠具體參數，也可先串一個電位器(可變電阻)，從大阻值向下調節，直到燈珠點亮和亮度適中時，測一下電位器實用的電阻值換上固定電阻即可。

led燈珠配電阻方法

led燈只支持直流，交流變直流后是300V左右，串聯一個led需要35V，串聯多少led后加電阻就行。

Led燈閃怎么加電阻

首先確定你的燈珠的額(e)定工作電壓，電流，然后根據你的實際供電最高電壓來配置電阻阻值，這里的電阻是限流用的。

假如你的燈珠是3V，20mA,你的電源最高是90v，一塊板子可以放3顆燈珠，那么這塊板子就是9V的電壓，兩塊板子串聯就得18V，供電最高電壓90V就需要電阻分擔90-18=72V電壓。LED的電流最好是80%額定電流，以便在亮度足夠的前提下保持其使用壽命。

假設我們讓它工作在15mA電流下，要配置的限流電阻阻值應為72V/0.015A=4.8K歐姆電阻，實際電阻阻值相近的有4.7K的色環電阻供使用。

單路板子計算好了，再根據每路的供電電流計算并聯路數的總電流，不能超過電源的最大功率。

led燈珠每隔多少個安一個電阻

LED燈珠所串聯的電阻的數量和阻值，一般和輸入的電壓及LED燈珠規格相關。

以上就是天成小編對于led燈珠為什么加電阻 led燈珠如何配限流電阻問題和相關問題的解答了，希望對你有用 【責任編輯：燈漂亮】